View LTST-C19HE2WT_7556731.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on technology corporation property of lite-on only features * meet rohs, green product. * extra thin (0.40hmm) full color smd chip led. * package in 8mm tape on 7" diameter reels. * compatible with automatic placement equipment. * compatible with infrared and vapor phase reflow solder process. * eia std package. * i.c. compatible. package dimensions part no. lens source color pin assignment ingan green 1 ingan blue 2 LTST-C19HE2WT white diffused alingap red 3 notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.10 mm (.004") unless otherwise noted. part no. : LTST-C19HE2WT page : 1 of 11 bns-od-c131/a4
lite-on technology corporation property of lite-on only absolute maximum ratings at ta=25 LTST-C19HE2WT parameter blue green red unit power dissipation 80 80 75 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 100 100 80 ma dc forward current 20 20 30 ma derating linear from 25 c 0.25 0.25 0.4 ma/ c reverse voltage 5 5 5 v operating temperature range -20 c to + 80 c storage temperature range -30 c to + 100 c wave soldering condition 260 c for 5 seconds infrared soldering condition 260 c for 5 seconds vapor phase soldering condition 215 c for 3 minutes part no. : LTST-C19HE2WT page : 2 of 11 bns-od-c131/a4
lite-on technology corporation property of lite-on only suggestion profile: (1) suggestion ir reflow profile for normal process (2) suggestion ir reflow profile for pb free process recommended profile between assemble and heat-resistance line the profile is available that m ust to use sna g cu solder paste part no. : LTST-C19HE2WT page : 3 of 11 bns-od-c131/a4
lite-on technology corporation property of lite-on only electrical optical characteristics at ta=25 LTST-C19HE2WT parameter symbol blue green red unit test condition min. 28.0 71.0 45.0 typ. - - - luminous intensity iv max. 112.0 280.0 180.0 mcd if = 20ma note 1 viewing angle 2 1/2 typ. 130 deg note 2 (fig.6) peak emission wavelength peak typ. 468 520 632 nm measurement @peak (fig.1) min. 465 520 617 dominant wavelength d max. 475 530 631 nm if = 20ma note 3 spectral line half-width ? typ. 26 35 17 nm min. 2.90 2.90 1.80 typ. - - - forward voltage vf max. 3.50 3.50 2.40 v if = 20ma reverse current ir max. 10 10 10 a vr = 5v notes: 1. luminous intensity is measured with a li ght sensor and filter combination that approximates the cie eye-response curve. 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. caution in esd: static electricity and surge damages the led . it is recommend to use a wrist band or anti-electrostatic glove when handling the led. all devi ces, equipment and machinery must be properly grounded. part no. : LTST-C19HE2WT page : 4 of 11 bns-od-c131/a4
lite-on technology corporation property of lite-on only bin code list part no. : LTST-C19HE2WT page : 5 of 11 bns-od-c131/a4 luminous intensity color : blue , unit : mcd @20ma bin code min. max. n 28.0 45.0 p 45.0 71.0 q 71.0 112.0 tolerance on each intensity bin is +/-15% luminous intensity color : green , unit : mcd @20ma bin code min. max. q 71.0 112.0 r 112.0 180.0 s 180.0 280.0 tolerance on each intensity bin is +/-15% luminous intensity color : red , unit : mcd @20ma bin code min. max. p 45.0 71.0 q 71.0 112.0 r 112.0 180.0 tolerance on each intensity bin is +/-15%
lite-on technology corporation property of lite-on only typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) part no. : LTST-C19HE2WT page : 6 of 11 bns-od-c131/a4
lite-on technology corporation property of lite-on only cleaning do not use unspecified chemical liquid to clean led they could harm the package. if clean is necessary, immerse the led in ethyl alcohol or in isopropyl alcohol at normal temperature for less one minute. suggest soldering pad dimensions package dimensions of tape and reel notes: 1. all dimensions are in millimeters (inches). part no. : LTST-C19HE2WT page : 7 of 11 bns-od-c131/a4
lite-on technology corporation property of lite-on only notes: 1. empty component pockets sealed with top cover tape. 2. 7 inch reel-3000 pieces per reel. 3. minimum packing quantity is 500 pcs for remainders. 4. the maximum number of consecutive missing lamps is two. 5. in accordance with ansi/eia 481-1-a-1994 specifications. part no. : LTST-C19HE2WT page : 8 of 11 bns-od-c131/a4
lite-on technology corporation property of lite-on only part no. : LTST-C19HE2WT page : 9 of 11 bns-od-c131/a4 cautions 1. application the leds described here are intended to be used fo r ordinary electronic equipment (such as office equipment, communication equipment and household applications).consult liteon?s sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the leds may directly jeopardize lif e or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their origin al packaging are ir-reflowed within one week. for extended storage out of their original packaging, it is recommended that the leds be stored in a sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient. leds stored out of their original packaging for mo re than a week should be baked at about 60 deg c for at least 24 hours before solder assembly. 3. cleaning use alcohol-based cleaning solvents such as isopropyl alcohol to clean the led if necessary. 4. soldering recommended soldering conditions: reflow soldering wave soldering soldering iron pre-heat pre-heat time peak temperature soldering time 120~150c 120 sec. max. 240c max. 10 sec. max. pre-heat pre-heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 10 sec. max. temperature soldering time 300c max. 3 sec. max. (one time only) 5. drive method an led is a current-operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model a circuit model b led led (a) recommended circuit. (b) the brightness of each led might appear different due to the differences in the i-v characteristics of those leds. 6. esd (electrostatic discharge) static electricity or power surge will damage the led. suggestions to prevent esd damage: ? use of a conductive wrist band or anti-electrostatic glove when handling these leds. ? all devices, equipment, and machinery must be properly grounded. ? work tables, storage racks, etc. should be properly grounded. ? use ion blower to neutralize the static charge which might have built up on surface of the led?s plastic lens as a result of friction between leds during storage and handling.
lite-on technology corporation property of lite-on only part no. : LTST-C19HE2WT page : 10 of 11 bns-od-c131/a4 esd-damaged leds will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or ? no lightup ? at low currents. to verify for esd damage, check for ? lightup ? and vf of the suspect leds at low currents. the vf of ? good ? leds should be >2.0v@0.1ma for ingan product and >1.4v@0.1ma for alingap product. 7. reliability test classification test item test condition reference standard operation life ta= under room temperature as per data sheet maximum rating * test time= 1000hrs (-24hrs,+72hrs)*@20ma. mil-std-750d:1026 (1995) mil-std-883d:1005 (1991) jis c 7021:b-1 (1982) high temperature high humidity storage ir-reflow in-board, 2 times ta= 655 ,rh= 90 95% * test time= 240hrs2hrs mil-std-202f:103b(1980) jis c 7021:b-11(1982) high temperature storage ta= 1055 * test time= 1000hrs (-24hrs,+72hrs) mil-std-883d:1008 (1991) jis c 7021:b-10 (1982) endurance test low temperature storage ta= -555 * test time=1000hrs (-24hrs,+72h rs) jis c 7021:b-12 (1982) temperature cycling 105 25 -55 25 30mins 5mins 30mins 5mins 10 cycles mil-std-202f:107d (1980) mil-std-750d:1051(1995) mil-std-883d:1010 (1991) jis c 7021:a-4(1982) thermal shock ir-reflow in-board, 2 times 85 5 -40 5 10mins 10mins 10 cycles mil-std-202f:107d(1980) mil-std-750d:1051(1995) mil-std-883d:1011 (1991) solder resistance t.sol= 260 5 dwell time= 10 1secs mil-std-202f:210a(1980) mil-std-750d:2031(1995) jis c 7021:a-1(1982) ir-reflow normal process ramp-up rate(183 to peak) +3 / second max temp. maintain at 125(25) 120 seconds max temp. maintain above 183 60-150 seconds peak temperature range 235 +5/-0 time within 5c of actual peak temperature (tp) 10-30 seconds ramp-down rate +6 /second max mil-std-750d:2031.2(1995) j-std-020(1999) ir-reflow pb free process ramp-up rate(217 to peak) +3 / second max temp. maintain at 175(25) 180 seconds max temp. maintain above 217 60 -150 seconds peak temperature range 260 +0/ -5 time within 5c of actual peak temperature (tp) 20-40 seconds ramp-down rate +6 /second max mil-std-750d:2031.2(1995) j-std-020(1999) environmental test solderability t.sol= 235 5 immersion time 20.5 sec immersion rate 252.5 mm/sec coverage R 95% of the dipped surface mil-std-202f:208d(1980) mil-std-750d:2026(1995) mil-std-883d:2003(1991) iec 68 part 2-20 jis c 7021:a-2(1982) 8. others the appearance and specifications of the product may be modified for improvement without prior notice.
lite-on technology corporation property of lite-on only 9. suggested checking list training and certification 1. everyone working in a static-safe area is esd-certified? 2. training records kept and re-certification dates monitored? static-safe workstation & work areas 1. static-safe workstation or work-areas have esd signs? 2. all surfaces and objects at all static-safe wo rkstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd sensitive (esds) items wears wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds items identified by eia-471 labels on item or packaging? 2. all esds items completely inside properly cl osed static-shielding containers when not at static-safe workstation? 3. no static charge generators (e.g. plastics) inside shielding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycles? others 1. audit result reported to entity esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records complete and on file? part no. : LTST-C19HE2WT page : 11 of 11 bns-od-c131/a4

▲Up To Search▲

Price & Availability of LTST-C19HE2WT

	To Download LTST-C19HE2WT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .